{"id":1177,"date":"2026-10-14T10:35:35","date_gmt":"2026-10-14T10:35:35","guid":{"rendered":"https:\/\/daix488.sg-host.com\/?post_type=product&p=1177"},"modified":"2026-10-15T10:43:49","modified_gmt":"2026-10-15T10:43:49","slug":"astm-f1295-ti-6al-7nb-titanium-plate-sheet","status":"publish","type":"product","link":"https:\/\/www.htn-ti.com\/ru\/product\/astm-f1295-ti-6al-7nb-titanium-plate-sheet\/","title":{"rendered":"ASTM F1295 Ti-6Al-7Nb Titanium Plate & Sheet"},"content":{"rendered":"\t\t
\n\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Product Overview<\/h2>\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

ASTM F1295-24 titanium plate and sheet are wrought Ti-6Al-7Nb alpha-beta alloy flat products for surgical implant manufacture, UNS R56700. Aluminum stabilizes alpha and niobium stabilizes beta. This vanadium-free alloy combines high specific strength, corrosion resistance, biological suitability and established medical processing capability.<\/p>

Products may be supplied as annealed hot-rolled plate, cold-rolled sheet, strip or contract-finished flat stock. Strip is normally \u22644.76 mm thick and <610 mm wide; sheet is \u22644.76 mm thick and \u2265610 mm wide; plate is >4.76 mm thick, \u2265254 mm wide and more than five times as wide as thick, covered through 101.60 mm thickness. Special sizes require agreement.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t\t\t\t\t\t
<\/colgroup>
Specification<\/strong><\/td>Cold-Rolled Titanium Sheet<\/strong><\/td>Hot-Rolled Titanium Plate<\/strong><\/td><\/tr>
Standard<\/strong><\/td>ASTM F1295<\/td><\/tr>
Grades<\/strong><\/td>Ti-6Al-7Nb<\/td><\/tr>
Thickness<\/strong><\/td>0.3\u20134.75 mm<\/td>5\u201360 mm; Customizable up to 100 mm<\/td><\/tr>
Standard Stock Thicknesses<\/strong><\/td>0.5 \/ 0.6 \/ 0.8 \/ 1.0 \/ 1.5 \/ 2.0 \/ 2.5 \/ 3.0 \/ 4.0mm<\/td>5 \/ 6 \/ 8 \/ 10 \/ 12 \/ 15 \/ 20 \/ 25 \/ 30 \/ 35 \/ 40 \/ 50 \/ 60 mm<\/td><\/tr>
Width<\/strong><\/td>400\u20131200 mm<\/td>400\u20132000 mm<\/td><\/tr>
Length<\/strong><\/td>1000\u20133000 mm<\/td>1000\u20136000 mm<\/td><\/tr>
Note<\/strong><\/td>Sheet Thickness \u2264 4.75 mm<\/td>Medical Titanium Plate & Sheet Typical thickness 0.5\u201320 mm; width \u22641200 mm; polished or pickled surfaces available.<\/td><\/tr><\/tbody><\/table><\/div>

Medical-use boundary:<\/strong> ASTM F1295-compliant plate and sheet are medical-device raw material, not an approved finished implant. The device manufacturer remains responsible for design, forming\/joining, fatigue, surface treatment, cleaning, sterilization, biological evaluation, risk management and regulatory compliance.<\/p><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t
\n\t\t\t\t\t

Main Characteristics<\/h3>\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t
  • Vanadium-free medical alpha-beta alloy:<\/strong> Approximately 7% Nb replaces V as the beta stabilizer while retaining high strength and useful processing behavior. Grade, specification and UNS identification must remain consistent with ASTM F1295 \/ R56700.<\/li>
  • Controlled chemistry:<\/strong> Al is 5.50-6.50% and Nb is 6.50-7.50%, with limits on Ta, Fe, O, C, N, H and residuals. Hydrogen is sampled from finished product to control pickup during pickling, heat treatment and finishing.<\/li>
  • Good biocompatibility:<\/strong> Stable TiO2, Nb2O5 and Al2O3 surface oxides and long medical use support implant applications. F1295 raw-material compliance does not approve the finished device; applicable biological evaluation such as ISO 10993 remains required.<\/li>
  • Good corrosion resistance:<\/strong> Performance is generally excellent in saline, body fluids and many chloride environments, but fretting, crevices, dissimilar-metal coupling, fluoride media and surface contamination require device-level evaluation.<\/li>
  • Weldable with strict shielding:<\/strong> Qualified laser, electron-beam, GTAW\/TIG or resistance processes may be used. The pool, back side and hot heat-affected zone require full inert-gas protection. Sheet welding must also control heat input, distortion and residual stress.<\/li>
  • High strength with controlled formability:<\/strong> Annealed flat product can be sheared, stamped, bent, drawn to a limited extent and machined, but springback is significant. Room-temperature bend performance is verified by a 105\u00b0 test using a 9T or 10T mandrel according to thickness.<\/li><\/ul>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t

    Chemical Composition<\/h3>\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t

    The following mass-percent limits apply to ASTM F1295-24 Ti-6Al-7Nb (UNS R56700). Formal purchasing and acceptance are governed by the contract edition, official ASTM text and original mill report:<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t

    \n\t\t\t\t\t\t\t\t\t
    Element<\/strong><\/td>ASTM F1295 Ti-6Al-7Nb requirement<\/strong><\/td><\/tr>
    Aluminum, Al<\/strong><\/td>5.50-6.50%<\/td><\/tr>
    Niobium, Nb<\/strong><\/td>6.50-7.50%<\/td><\/tr>
    Tantalum, Ta<\/strong><\/td>\u22640.50%<\/td><\/tr>
    Iron, Fe<\/strong><\/td>\u22640.25%<\/td><\/tr>
    Oxygen, O<\/strong><\/td>\u22640.20%<\/td><\/tr>
    Carbon, C<\/strong><\/td>\u22640.08%<\/td><\/tr>
    Nitrogen, N<\/strong><\/td>\u22640.05%<\/td><\/tr>
    Hydrogen, H<\/strong><\/td>\u22640.009%<\/td><\/tr>
    Residual elements, each<\/strong><\/td>\u22640.10%<\/td><\/tr>
    Residual elements, total<\/strong><\/td>\u22640.40%<\/td><\/tr>
    Titanium, Ti<\/strong><\/td>Balance<\/td><\/tr><\/tbody><\/table><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t

    Technical references: ASTM F1295-24 official edition information, publicly available ASTM F1295 technical tables, and producer data for TIMETAL 367 \/ ATI 6-7.<\/p>

    • Aluminum and niobium:<\/strong> Al is 5.50-6.50% and Nb is 6.50-7.50%. Homogeneity, beta transus, melting and thermomechanical processing jointly determine the final alpha-beta microstructure and properties.<\/li>
    • Tantalum and interstitials:<\/strong> Ta\u22640.50%, Fe\u22640.25%, O\u22640.20%, C\u22640.08%, N\u22640.05% and H\u22640.009%. The stringent hydrogen limit requires control of pickup during pickling, heat treatment, cleaning and storage.<\/li>
    • Residuals:<\/strong> Common requirements are \u22640.10% each and \u22640.40% total. The heat-specific report should cover all required elements and remain traceable to heat, lot and plate identification.<\/li>
    • Titanium content:<\/strong> The specification states Titanium: Balance. A nominal grade or medical-grade claim does not replace heat-specific analysis, the material report and contract testing.<\/li><\/ul>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
      \n\t\t\t\t
      \n\t\t\t\t\t

      Mechanical Properties<\/h3>\t\t\t\t<\/div>\n\t\t\t\t
      \n\t\t\t\t\t\t\t\t\t

      ASTM F1295 specifies room-temperature longitudinal and transverse requirements for annealed plate, sheet and strip: \u2265900 MPa ultimate tensile strength, \u2265800 MPa 0.2% yield strength and \u226510% elongation. Applicable sheet\/strip is cold-bent through 105\u00b0 without outside-surface fracture: 9T below 1.78 mm, 10T from 1.78 to 4.76 mm; the bend test does not apply above 4.76 mm. Formal acceptance follows the contract edition.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t

      \n\t\t\t\t\t\t\t\t\t
      Property<\/strong><\/td>ASTM F1295 annealed flat-product minimum<\/strong><\/td>Note<\/strong><\/td><\/tr>
      Ultimate tensile strength<\/strong><\/td>\u2265900 MPa<\/td>Longitudinal and transverse<\/td><\/tr>
      0.2% yield strength<\/strong><\/td>\u2265800 MPa<\/td>Longitudinal and transverse<\/td><\/tr>
      Elongation<\/strong><\/td>\u226510%<\/td>50 mm gauge normally at \u22651.6 mm; thinner by agreement<\/td><\/tr><\/tbody><\/table><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t
      \n\t\t\t\t\t\t\t\t\t

      ASTM F1295 Ti-6Al-7Nb Annealed Plate & Sheet Minimum Requirements<\/strong><\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t

      \n\t\t\t\t\t\t\t\t\t
      Property<\/strong><\/td>Ti-6Al-7Nb annealed reference<\/strong><\/td><\/tr>
      Ultimate tensile strength<\/strong><\/td>ASTM minimum: 900 MPa<\/td><\/tr>
      0.2% yield strength<\/strong><\/td>ASTM minimum: 800 MPa<\/td><\/tr>
      Elongation<\/strong><\/td>ASTM minimum: 10%<\/td><\/tr>
      Elastic modulus<\/strong><\/td>Typical approx. 105-120 GPa<\/td><\/tr><\/tbody><\/table><\/div>

      Important:<\/strong> Tensile requirements apply longitudinal and transverse to rolling direction. At \u22651.6 mm thickness, elongation normally uses a 50 mm gauge length; below 1.6 mm the method may be agreed. Bend specimens are cold-bent through 105\u00b0 without outside-surface fracture: 9T below 1.78 mm, 10T at 1.78-4.76 mm, and not applicable above 4.76 mm.<\/p><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

      \n\t\t\t\t
      \n\t\t\t\t\t

      HTN Supply and Quality Documentation<\/h3>\t\t\t\t<\/div>\n\t\t\t\t
      \n\t\t\t\t\t\t\t\t\t

      HTN organizes ASTM F1295-24 Ti-6Al-7Nb medical titanium plate and sheet supply to customer purchase requirements. Material is produced by qualified titanium-mill resources. Original mill reports, heat\/plate traceability, chemistry, longitudinal\/transverse mechanical properties, bend test, microstructure, beta-transus and ultrasonic records can be supplied as agreed. HTN reviews edition, dimensions, tolerances, annealed condition, surface, flatness, rolling direction, edges and packaging, and can arrange retesting, cut-to-size processing, clean packaging and third-party inspection.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

      \n\t\t\t\t
      \n\t\t\t\t\t

      Typical Applications<\/h3>\t\t\t\t<\/div>\n\t\t\t\t
      \n\t\t\t\t\t\t\t\t\t
      • raw material for orthopedic trauma fixation plates, bone plates and related load-bearing implant components;<\/li>
      • cranio-maxillofacial reconstruction plates, spinal implant components and joint-system parts;<\/li>
      • dental, surgical-instrument and other medical-device components requiring high-strength thin sections;<\/li>
      • flat stock for precision stamping, bending, machining or hybrid additive\/subtractive manufacturing;<\/li>
      • medical-device parts requiring high specific strength, good damage tolerance and corrosion resistance;<\/li>
      • hot-rolled plate, cold-rolled sheet, ground plate and cut-to-size flat stock supplied to customer drawings;<\/li>
      • medical-device research, prototypes and custom implant material;<\/li>
      • international projects when ISO 5832-11, regulatory and customer supplementary requirements are also met.<\/li><\/ul>

        Application boundary:<\/strong> ASTM F1295 Ti-6Al-7Nb plate and sheet are raw material for surgical implant manufacture, not an approved finished implant. The final device must separately meet applicable regulations, design validation, fatigue evaluation, biological evaluation, cleaning, sterilization and traceability requirements.<\/p><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

        \n\t\t\t\t
        \n\t\t\t\t\t
        Request a Quote<\/div>\t\t\t\t<\/div>\n\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t

        Fill in the form below and our team will be happy to assist you<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t

        \n\t\t\t\t\t\t\t
        \t\t
        \n\t\t\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t
        \n\t\t\t
        \n\t\t\t\t\t\t
        \n\t\t\t\t\t\t\t
        \n\t\t\t\n\t\t\t\n\t\t\t\n\n\t\t\t\t\t\t\t\n\t\t\t\n\t\t\t
        \n\t\t\t\t\t\t\t\t
        \n\t\t\t\t\t\t\t\t\t\t\t\t